About HCE
HCE manufactures commercial helmet cleaning and disinfection equipment in Foshan, China, shipping order-configured machines to operators and distributors.
HCE manufactures commercial helmet cleaning, disinfection, and drying equipment. We build order-configured machines at our facility in Foshan and ship them to operators, distributors, and OEM partners internationally.
The company name used for this site is Foshan Weixianwu Internet Services Co., Ltd., Foshan City, Guangdong Province, China.
What we build
Three commercial configurations, each confirmed against the destination market’s voltage and the site’s expected throughput:
- HCE-S1 — a single-chamber cabinet for workshops, gear retail, rental counters, and driving schools.
- HCE-D2 — a two-zone working configuration with simultaneous operation to be confirmed, for higher-traffic sites such as ride-hailing hubs, fuel stations, and transit stations.
- HCE-K2 — a self-service configuration with multilingual interface, project-specific payment and monitoring options, and door controls to be confirmed.
Treatment modules, drying methods, cycle settings and material compatibility are documented for each configuration. Request the order-specific technical sheet rather than assuming every model uses the same process.
Who we work with
Motorcycle dealerships and repair workshops, helmet and gear rental operators, delivery and ride-hailing fleets, driving schools, karting and motorsport venues, parking and fuel-station operators, and regional distributors who want to carry the category in their own market.
We supply OEM and private-label configurations, and we run a distributor program with defined regional terms.
Guides and operating references
Alongside the equipment, we publish practical guides on selecting, operating, and maintaining helmet cleaning equipment — cycle planning, throughput calculation, maintenance schedules, and cleaning-versus-disinfection procedure.
These guides are written to be useful during an evaluation, including when the reader is comparing our machines against other options. We favour clear definitions, visible assumptions, and practical evaluation steps, and we organize coverage around the decision a reader actually needs to make.
Scope and verification
Our guides do not replace manufacturer instructions, safety data sheets, infection-control advice, or the requirements that apply in a reader’s jurisdiction. Product claims, material compatibility, and operating conditions should be verified for the specific helmet, equipment model, chemical, and use case in question.
Published parameter tables distinguish confirmed values from fields awaiting confirmation. K2 rated power is 1800 W and maximum power is 2650 W, confirmed by the company representative on 21 September 2026. Final dimensions, electrical requirements, cycle settings, and included modules are confirmed in the technical sheet attached to each quotation.
When we correct or materially update an article, we make the change visible through the article’s updated date.
Documents to request for a project
Ask for the model-specific technical sheet, configuration and packing list, pre-shipment inspection scope, commissioning instructions, consumable requirements and written service terms. Factory images, test reports and certificates should identify the equipment or process they document.
Compare the equipment configurations, review the quotation breakdown, or contact HCE with your destination and operating requirements.
How to evaluate a project with HCE
Start with a short description of the proposed operation: location, customer type, quantity, staffing and site conditions. A workshop adding a counter service needs a different discussion from a distributor planning a branded range or an operator installing a public self-service point.
Use the first discussion to identify the equipment configuration and the questions that need technical review. Keep the configuration, priced options and shipment responsibilities together in the written proposal. If a requirement changes, check whether the specification, operating instructions or commercial terms need updating as well.
Before ordering, ask how the delivered equipment will be identified and checked. The acceptance scope can include the configuration list, visible condition, interface language, accessories, documentation and agreed functional tests. The actual test methods and results must come from the equipment review; a general website description is not an inspection report.
For a customized project, use the OEM brief and deliverable checklist. For an operating site, use the business pilot guide to gather the demand and servicing information that a product specification cannot supply.
Reading specifications, examples and illustrations
Confirmed parameters describe the specific fact and model identified on the page. A configuration option still needs to be included in the order to define what is delivered. A calculator assumption is an editable planning input, and a conceptual application image does not establish a verified customer installation.
When reviewing a technical report or reference, check which model, material, process and conditions it actually covers. Request clarification where an intended use differs. This distinction is particularly important for treatment efficacy, payment compatibility, environmental protection and operating capacity.
Send corrections with the page URL, model reference and the information that needs clarification through the factory contact page. Supplying the relevant document version helps keep the quotation, product information and operating guides consistent.